manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 47 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 47

 

2-35

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

MAC_LIMIT Messages

Error Message   

IGMP_QUERIER-6-PIM_DISABLED: The IGMP querier is now operationally 

enabled in VLAN [dec] because PIM is no longer enabled on the SVI. 

Explanation   

This message means that Protocol-Independent Multicast (PIM) is disabled on the 

switch virtual interface (SVI), and the IGMP querier function is now enabled. [dec] is the VLAN 
number.

Recommended Action   

No action is required.

Error Message   

IGMP_QUERIER-6-SNOOPING_ENABLED: The IGMP querier is now operationally 

enabled in VLAN [dec] because IGMP snooping is no longer disabled. 

Explanation   

This message means that IGMP snooping was enabled. As a result, the IGMP querier 

function is now enabled. [dec] is the VLAN number.

Recommended Action   

No action is required.

MAC_LIMIT Messages

This section contains the MAC_LIMIT messages, which describe the entries in the MAC address table.

Error Message   

MAC_LIMIT-4-DROP: Vlan [dec] with Configured limit = [dec] has 

currently [dec] Entries. 

Explanation   

This message means that the number of MAC address table entries for a VLAN is less 

than or equal to the maximum number allowed. The first [dec] is the VLAN ID, the second [dec] is 
the maximum number of MAC address entries, and the third [dec] is the number of entries in the 
MAC address table.

Recommended Action   

Your system administrator configures an action.

Error Message   

MAC_LIMIT-4-ENFORCE: Enforcing limit on Vlan [dec] with Configured 

limit = [dec]. 

Explanation   

This message means that the number of MAC address entries for the VLAN exceeds the 

maximum number allowed and that the configured action is to limit the number of entries to the 
maximum allowed. The first [dec] is the VLAN ID, and the second [dec] is the maximum number 
of MAC address entries.

Recommended Action   

Your system administrator configures an action.

Summary of Contents for ME 2400











































































































Reviews:

No comments