manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 43 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 43

 

2-31

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

IDBMAN Messages

Error Message   

HLFM-3-MAP_ERROR: IP address [IP_address] not in mac tables, 

mac-address [enet], vlan [dec].

Explanation   

This message means that the IP address and MAC address tables are out of sync. 

[IP_address] is the IP address, [enet] is the MAC address, and [dec] is the VLAN ID.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-3

.

Error Message   

HLFM-3-MOD_SD: Failed to modify Station Descriptor with index [dec], 

vlan [dec], di [dec], error [dec], mad [dec], ref-count [dec]. 

Explanation   

This message means that the forwarding manager attempted to modify a station 

descriptor that is no longer in use or is invalid. The first [dec] is the station index, the second [dec] 
is the VLAN ID, the third [dec] is the destination index, the fourth [dec] is the error code, the fifth 
[dec] is the MAC address descriptor, and the sixth [dec] is the ref-count for this MAC address 
descriptor.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-3

.

IDBMAN Messages

This section contains the interface description block manager (IDBMAN) messages. 

Note

These messages apply only to the Cisco ME 3400E and ME 3400 switches.

Error Message   

IDBMAN-3-AGGPORTMISMATCH: [chars]: [chars]([dec] / [dec]) does not 

match internal slot/port state [chars]([dec] / [dec]). 

Explanation   

This message means that there is an internal error that caused the software to use an 

invalid aggregate port. The first [chars] is the name of the function where the error occurred. The 
second and third [chars] are the port-channel names, and the ([dec] / [dec]) are the slot and port 
numbers (slot/port).

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-3

.

Summary of Contents for ME 2400











































































































Reviews:

No comments