Cisco Catalyst 4500 Series Installation Manual Download Page 144 | Manualshive

Page: 144 / 194

background image

Chapter 4 Removing and Replacing FRUs

Replacing Backplane Modules on a Catalyst 4507R or 4510R Switch

4-30

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Verify the New Modules

After the switch is reassembled and power is restored, connect a terminal to the
supervisor engine and monitor the boot process. Look for the following messages
(or any others), which may indicate a problem with the replaced modules:

00:00:20: %C4K_SUPERVISOR-2-MUXBUFFERNOTPRESENT: Mux buffer

(WS-X4K-MUX) 3 is not present

00:00:20: %C4K_SUPERVISOR-2-MUXBUFFERNOTPRESENT: Mux buffer

(WS-X4K-MUX) 4 is not present

00:00:20: %C4K_SUPERVISOR-2-MUXBUFFERNOTPRESENT: Mux buffer

(WS-X4K-MUX) 7 is not present

The above messages (either at startup or output from a

show logging

command)

indicate that the mux-buffer is not present in slots 3, 4 and 7. You need to reinsert
and reseat the modules in those slots.

If the switch has already started up, you may also verify the correct function of
the new modules with the

show logging

command.

«
...
142
143
144
145
146
...
»

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

Brand: Sagem Pages: 19

Brand: Ubiquiti Pages: 23

Avenue Express Control Panel

Brand: Ensemble Designs Pages: 19

Brand: WaiLan Pages: 27

Sentry Global Security Modem

Brand: Server Technology Pages: 22

Brand: WAGO Pages: 2

Brand: Hunter Pages: 2

Brand: Comtrend Corporation Pages: 4

Brand: Linksys Pages: 6

Brand: MaxComm Pages: 10

Brand: Alcatel-Lucent Pages: 60

Brand: NetComm Pages: 34

Brand: TRENDnet Pages: 3

Brand: Korenix Pages: 3

Brand: Eaton Pages: 24

Brand: Billion Pages: 127

Brand: Asus Pages: 11

Brand: Asus Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands