Cisco Catalyst 4500 Series Installation Manual Download Page 182

Page: 182 / 194

Appendix A Specifications

Catalyst 4500 Series Power Supplies

A-18

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Table A-12

2800 W AC-Input Power Supply Specifications

Item

Specification

Minimum software requirement

Cisco IOS Release 12.1(13)EW

Catalyst Operating System software

version 7.5 (1)

Power over Ethernet

Supported, up to 1400 W

(240 Cisco phones in combined mode)

AC-input type

Autoranging input with power factor corrector

AC-input voltage

200 to 240 VAC (±10% for full range)

AC-input current

16 A maximum at 200 VAC

AC-input frequency

50/60 Hz (nominal) (±3% for full range)

Maximum KVA rating

3.52 KVA

Power supply output

2800 W maximum

12 V @113.3 A, 3.3 V @12.1 A (Data)

–50 V @28 A (PoE)

1360 W+ 40 W redundant mode (Data)

2473 W maximum in combined mode (Data)

1400 W maximum each in redundant mode (PoE)

2333 W maximum in combined mode (PoE)

Max heat dissipation

2387 BTUs/hr.

Output holdup time

20 ms minimum

Summary of Contents for Catalyst 4500 Series



































































































































































































Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands

Cisco Catalyst 4500 Series, Installation Manual

Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands