manualshive.com logo in svg

Cisco Catalyst 4500 Series, Installation Manual

The Cisco Catalyst 4500 Series is a powerful network switch offering seamless connectivity and efficient performance. To unlock the full potential of this product, users can easily download the comprehensive Command Reference Manual for free from our website, ensuring hassle-free operation and optimal network management.

Share
Download
background image

   

Chapter 3      Installing the Switch in a Rack

3-2

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Note

The blank line card (C4K-SLOT-CVR-E) must be installed when either of the 
following two situations occur:

  •

If your Catalyst 4507R or Catalyst 4510R switch chassis has a Supervisor 
Engine 6-E (WS-X45-SUP6-E) or a Supervisor Engine 6L-E 
(WS-X45-SUP6L-E) installed in slot 1 and slot 2 is empty, you must install 
the blank line card (C4K-SLOT-CVR-E) in slot 2 rather than a blank 
faceplate (C4K-SLOT-CVR) . A blank faceplate covering the slot 2 opening 
does not direct sufficient airflow to adequately cool the Supervisor 
Engine 6-E or the Supervisor Engine 6L-E.

  •

If your Catalyst 4507R or Catalyst 4510R switch chassis has a Supervisor 
Engine 6-E (WS-X45-SUP6-E) or a Supervisor Engine 6L-E 
(WS-X45-SUP6L-E) installed in slot 2 and slot 1 is empty, you must install 
the blank line card (C4K-SLOT-CVR-E) in slot 1 rather than a blank 
faceplate (C4K-SLOT-CVR) . A blank faceplate covering the slot 1 opening 
does not direct sufficient airflow to adequately cool the Supervisor 
Engine 6-E or the Supervisor Engine 6L-E.

Note

When populating empty chassis slots, start filling the upper slots first and work 
down to the bottom slots.

This chapter describes how to install Catalyst 4500 series switches in a rack. For 
first-time installations, perform the procedures in the following sections in the 
order listed:

  •

Checking the Shipping Container Contents, page 3-3

  •

Rack-Mounting the Switch, page 3-4

Note

Before starting the installation procedures in this chapter, complete the 
site-planning checklist in 

Table 2-2

 of 

Chapter 2, “Preparing for Installation.”

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

Ubiquiti M900 Quick Start Manual preview
M900
Brand: Ubiquiti Pages: 24
National Instruments SCXI-1121 User Manual preview
SCXI-1121
Brand: National Instruments Pages: 162
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
TP-Link TD-8817 User Manual preview
TD-8817
Brand: TP-Link Pages: 73
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Brand: LogLogic Pages: 30
Mercusys MR30G Quick Installation Manual preview
MR30G
Brand: Mercusys Pages: 35
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Brand: ADTRAN Pages: 46
Macsense MPC-200 User Manual preview
MPC-200
Brand: Macsense Pages: 13
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
Draytek Vigor 2700G Specifications preview
Vigor 2700G
Brand: Draytek Pages: 2
Genie IP8ESP User Manual preview
IP8ESP
Brand: Genie Pages: 6
HELVAR Imagine 920 Installation Manual preview
Imagine 920
Brand: HELVAR Pages: 2
Quantum QWCM Installation Manual preview
QWCM
Brand: Quantum Pages: 7
Lanner FW-7551 User Manual preview
FW-7551
Brand: Lanner Pages: 38
Allied Telesis AT-BSTACK1 Quick Install Manual preview
AT-BSTACK1
Brand: Allied Telesis Pages: 34
CalAmp Viper 100 User Manual preview
Viper 100
Brand: CalAmp Pages: 115
MiWire SeaWire Pro User Manual preview
SeaWire Pro
Brand: MiWire Pages: 24
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Brand: Ubiquiti Pages: 13

Brands by name

Popular brands

Load more brands