Cisco Catalyst 4500 Series Installation Manual Download Page 130 | Manualshive

Page: 130 / 194

background image

Chapter 4 Removing and Replacing FRUs

Removing and Replacing the Power Supply

4-16

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Installing a DC-Input Power Supply

This section describes how to install a DC-input power supply.

Required Tools

You will need the following tools to perform this procedure:

•

A Phillips screwdriver

•

A 10-mm wrench/socket

•

Connectors and wire for the DC circuit or circuits

Installation Procedure

Warning

Before performing any of the following procedures, ensure that power is
removed from the DC circuit.

Statement 1003

Warning

A readily accessible two-poled disconnect device must be incorporated in the
fixed wiring.

Statement 1022

Warning

This product requires short-circuit (overcurrent) protection, to be provided as
part of the building installation. Install only in accordance with national and
local wiring regulations.

Statement 1045

Warning

Use copper conductors only.

Statement 1025

Warning

When stranded wiring is required, use approved wiring terminations, such as
closed-loop or spade-type with upturned lugs. These terminations should be the
appropriate size for the wires and should clamp both the insulation and
conductor.

Statement 1002

«
...
128
129
130
131
132
...
»

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

Brand: NavigateWorx Pages: 71

Brand: Lorex Pages: 186

Brand: TP-Link Pages: 2

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

Brand: CyberTAN Pages: 67

Brand: JUMO Pages: 60

Brand: X-Micro Pages: 49

Brand: Airlink101 Pages: 13

Brand: Quantum Pages: 7

Brand: Intel Pages: 958

Brand: INNOSILICON Pages: 11

WebShare 141 WN

Brand: Atlantis Pages: 78

HomePNA PCI Adapter

Brand: City-Netek Pages: 18

Brand: MiLAN Pages: 155

Brand: NetComm Pages: 75

Brand: Proscend Pages: 93

Brand: Transition Networks Pages: 5

IKS-6728 Series

Brand: Moxa Technologies Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands