manualshive.com logo in svg

Cisco Catalyst 4500 Series, Installation Manual

The Cisco Catalyst 4500 Series is a powerful network switch offering seamless connectivity and efficient performance. To unlock the full potential of this product, users can easily download the comprehensive Command Reference Manual for free from our website, ensuring hassle-free operation and optimal network management.

Share
Download
background image

   

Chapter 5      Troubleshooting

Troubleshooting the Power Supply

5-6

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Troubleshooting the Power Supply

To help isolate a power subsystem problem, follow these steps:

Step 1

Check whether the power supply LED labeled GOOD is on or the LED labeled 
FAIL is on. (on the DC multi-input power supply, the LEDs are labeled INPUT 1, 
2, or 3 or OUTPUT FAIL.) 

Step 2

If the LED labeled GOOD is off or if the LED labeled FAIL is on, take the 
following steps:

  •

Ensure that the power supply is flush with the back of the chassis. 

  •

Unplug the power cord, loosen and reinstall the power supply, tighten the 
captive installation screws, and then plug in the power cord.

Step 3

If the LED labeled GOOD remains off, there might be a problem with the AC 
source or the power cable. Connect the power cord to another power source if one 
is available.

Step 4

If the LED labeled GOOD fails to light after you connect the power supply to a 
new power source, replace the power cord.

Note

If this unit has more than one power cord, repeat Step 1 through 

Step 4

 for 

each power input.

Step 5

If the LED labeled GOOD still fails to light when the switch is connected to a 
different power source with a new power cord, the power supply is probably 
faulty. Replace the power supply.

Step 6

If the LED labeled FAN OK fails to light when the switch is connected to a power 
source with a known good power cord, there is a malfunction in the fan that cools 
the power supply. Replace the power supply.

Step 7

If a second power supply is available, install it in the second power supply bay.

Step 8

Check that the LED labeled GOOD is on for the additional power supply. Check 
that the LED labeled FAIL is off.

Step 9

If the LEDs are not on, repeat the previous procedure to troubleshoot the second 
power supply. 

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

D-Link DSL-2730B Technical Support preview
DSL-2730B
Brand: D-Link Pages: 5
D-Link GO-SW-5E Quick Install Manual preview
GO-SW-5E
Brand: D-Link Pages: 2
Billion BiPAC 4500NZ(L) User Manual preview
BiPAC 4500NZ(L)
Brand: Billion Pages: 146
NetComm 3GM1WN Quick Start Manual preview
3GM1WN
Brand: NetComm Pages: 3
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
NETGEAR FS605 v3 Installation Manual preview
FS605 v3
Brand: NETGEAR Pages: 84
peplink balance ONE Manual preview
balance ONE
Brand: peplink Pages: 2
Abocom PLS342 Specification Sheet preview
PLS342
Brand: Abocom Pages: 2
Zalip CDG561 WE~P21 User Manual preview
CDG561 WE~P21
Brand: Zalip Pages: 77
Linksys EtherFast LNE100TX ver. 5 User Manual preview
EtherFast LNE100TX ver. 5
Brand: Linksys Pages: 42
UTStarcom UT-300R2U User Manual preview
UT-300R2U
Brand: UTStarcom Pages: 71
Tripp Lite N002-025-GY Specification Sheet preview
N002-025-GY
Brand: Tripp Lite Pages: 3
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Brand: V-Count Pages: 2
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
H3C AR 46-80 Installation Manual preview
AR 46-80
Brand: H3C Pages: 103
Manson Engineering Industrial SBC-6108 User Manual preview
SBC-6108
Brand: Manson Engineering Industrial Pages: 10
EMC VNX5300 Block Hardware Information Manual preview
VNX5300 Block
Brand: EMC Pages: 88
ZyXEL Communications Prestige 643 User Manual preview
Prestige 643
Brand: ZyXEL Communications Pages: 191

Brands by name

Popular brands

Load more brands