Cisco Catalyst 4500 Series Installation Manual Download Page 123 | Manualshive

Page: 123 / 194

background image

4-9

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Chapter 4 Removing and Replacing FRUs

Removing and Replacing the Power Supply

Figure 4-9

Plugging the Power Cord into the Power Supply

Step 10

Connect the other end of the power cord to an AC-power input source.

Caution

In a system with multiple power supplies, connect each power supply to a separate
AC power source. In the event of a power source failure, if the second source is
still available, it can maintain maximum overcurrent protection for each power
connection.

Step 11

Press the power switch down to the on (|) position (see

Figure 4-10

).

Figure 4-10

Powering On the Power Supply

79142

Power switch

79143

«
...
121
122
123
124
125
...
»

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

Brand: D-Link Pages: 12

Brand: Funkwerk Pages: 2

Brand: ZyXEL Communications Pages: 299

Brand: Macsense Pages: 13

Brand: Idis Pages: 17

IGS-5225-20T4C2X

Brand: Planet Pages: 16

NetCon FBR-1409TX

Brand: LevelOne Pages: 88

Brand: Keysight Technologies Pages: 106

Brand: Airvana Pages: 90

Q-SYS QIO-GP8x8

Brand: QSC Pages: 13

FiberTwist XGS2420

Brand: Genexis Pages: 7

Brand: Edgewater Networks Pages: 23

Brand: H3C Pages: 62

Brand: qpcom Pages: 4

Brand: C-Data Pages: 19

Brand: Ericsson Pages: 16

Brand: Huawei Pages: 3

Brand: Johnson Controls Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands