manualshive.com logo in svg

Cisco Catalyst 4500 Series, Installation Manual

The Cisco Catalyst 4500 Series is a powerful network switch offering seamless connectivity and efficient performance. To unlock the full potential of this product, users can easily download the comprehensive Command Reference Manual for free from our website, ensuring hassle-free operation and optimal network management.

Share
Download
background image

   

4-23

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Chapter 4      Removing and Replacing FRUs

Removing and Replacing the Chassis Fan Assembly

Removing the Fan Assembly

Warning

When removing the fan tray, keep your hands and fingers away from the 
spinning fan blades. Let the fan blades completely stop before you remove the 
fan tray. 

Statement 258

Caution

Never operate the system for an extended period if the fan assembly is removed 
or if it is not functioning properly. An over-temperature condition can cause 
severe equipment damage.

Follow these steps to remove the existing chassis fan assembly:

Step 1

Loosen the two captive installation screws on the fan assembly by turning them 
counterclockwise.

Step 2

Grasp the fan assembly with both hands and pull it outward; gently move it side 
to side if necessary to unseat it from the backplane. Slide it out of the chassis and 
place it in a safe place.

Installing the Fan Assembly

Follow these steps to install the new fan assembly:

Step 1

Hold the fan assembly with the fans facing to the right. 

Step 2

Place the fan assembly into the fan assembly bay so it rests on the chassis, and 
then lift the fan assembly up slightly, aligning the top and bottom guides.

Step 3

Slide the fan assembly into the chassis until the two captive installation screws 
make contact with the chassis.

Step 4

Using a screwdriver, tighten the two captive installation screws by turning them 
clockwise. 

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

D-Link AirPlus DWL-810 Owner'S Manual preview
AirPlus DWL-810
Brand: D-Link Pages: 25
Panasonic KX-UDS124 Important Information Manual preview
KX-UDS124
Brand: Panasonic Pages: 44
Abocom FW200 Specifications preview
FW200
Brand: Abocom Pages: 1
Quick Eagle Networks 5842 Specification Sheet preview
5842
Brand: Quick Eagle Networks Pages: 4
Draytek VigorIPPBX 2820 Series Quick Start Manual preview
VigorIPPBX 2820 Series
Brand: Draytek Pages: 29
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
AT&T Nighthawk M6 Pro Let'S Get Started preview
Nighthawk M6 Pro
Brand: AT&T Pages: 2
Patton electronics 1000RC User Manual preview
1000RC
Brand: Patton electronics Pages: 9
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
Gira 0535 00 Installation Instructions Manual preview
0535 00
Brand: Gira Pages: 6
1&1 Homeserver+ Quick Start Manual preview
Homeserver+
Brand: 1&1 Pages: 32
Sparklan WNFB-265AXI(BT) User Manual preview
WNFB-265AXI(BT)
Brand: Sparklan Pages: 14
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Brand: Dahua Pages: 33
Cabletron Systems SmartSwitch 8-slot User'S Reference Manual preview
SmartSwitch 8-slot
Brand: Cabletron Systems Pages: 150
DIGIWEB Box 7360 Quick Setup Manual preview
Box 7360
Brand: DIGIWEB Pages: 16
AirLive Ether-GSH24T v3 Quick Setup Manual preview
Ether-GSH24T v3
Brand: AirLive Pages: 2
hilscher netHOST NHST-T100 User Manua preview
netHOST NHST-T100
Brand: hilscher Pages: 75
InHand IR615-S Series User Manual preview
IR615-S Series
Brand: InHand Pages: 69

Brands by name

Popular brands

Load more brands