manualshive.com logo in svg

Cisco Catalyst 4500 Series, Installation Manual

The Cisco Catalyst 4500 Series is a powerful network switch offering seamless connectivity and efficient performance. To unlock the full potential of this product, users can easily download the comprehensive Command Reference Manual for free from our website, ensuring hassle-free operation and optimal network management.

Share
Download
background image

   

2-3

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Chapter 2      Preparing for Installation

Electrostatic Discharge

Sometimes, voltage is discharged to some of the pins of the connector and not 
others, or to some pins on the connector before others. This is known as a 
differential discharge event, which can damage the networking equipment being 
connected.

You can take the following measures to prevent ESD cable damage:

  •

Ground the cable before connecting the networking equipment. You can 
create a grounding cable using an RJ-45 patch cable by doing the following:

  –

Bare the wires on one end

  –

Connect the wires to a suitable and safe earth ground

  –

Connect the RJ-45 cable to a female RJ-45 connector

  •

Briefly connect all cables to the grounded cable before connecting to 
networking equipment.

  •

Leave cables from the networking equipment in the distribution closet 
connected to ports at user desktops. After you make connections on either 
side of the cable to networking equipment, the cable will not build up charge.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, which can occur when electronic cards or 
components are improperly handled, results in complete or intermittent failures. 
Port adapters and processor modules consist of printed circuit boards that are 
fixed in metal carriers. Electromagnetic interference (EMI) shielding and 
connectors are integral components of the carrier. Although the metal carrier 
helps to protect the board from ESD, use a preventive antistatic strap during 
handling.

Following are guidelines for preventing ESD damage:

  •

Always use an ESD wrist or ankle strap and ensure that it makes good skin 
contact. 

  •

Connect the equipment end of the strap to an unfinished chassis surface.

  •

When installing a component, use any available ejector levers or captive 
installation screws toproperly seat the bus connectors in the backplane or 
midplane. These devices prevent accidentalremoval, provide proper 
grounding for the system, and help to ensure that bus connectors areproperly 
seated.

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

IBM 2210 Installation And Initial Configuration Manual preview
2210
Brand: IBM Pages: 72
Makita 3606 Parts Breakdown preview
3606
Brand: Makita Pages: 2
3Com 3CR860-95 - OfficeConnect Secure Router Features And Benefits preview
3CR860-95 - OfficeConnect Secure Router
Brand: 3Com Pages: 2
3Com 3C905-TX Installation Manual preview
3C905-TX
Brand: 3Com Pages: 26
QNAP QMiroPlus-201W Quick Installation Manual preview
QMiroPlus-201W
Brand: QNAP Pages: 20
3Com 3C13886 - Router OC-3 ATM SML Flexible Interface... Installation Manual preview
3C13886 - Router OC-3 ATM SML Flexible Interface...
Brand: 3Com Pages: 171
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
Klark Teknik DN9650 Operator'S Manual preview
DN9650
Brand: Klark Teknik Pages: 50
E-TOP PR126g User Manual preview
PR126g
Brand: E-TOP Pages: 24
Intellinet 561051 Quick Install Manual preview
561051
Brand: Intellinet Pages: 12
VoiceLine InnoMedia MTA 3328-2R Getting Started Manual preview
InnoMedia MTA 3328-2R
Brand: VoiceLine Pages: 18
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
ATEN Slideaway CL1008 User Manual preview
Slideaway CL1008
Brand: ATEN Pages: 77
Tripp Lite N201-007-YW Specification Sheet preview
N201-007-YW
Brand: Tripp Lite Pages: 2
netsys NVF-2400S User Manual preview
NVF-2400S
Brand: netsys Pages: 164
Spirent A2-400 Installation Instructions Manual preview
A2-400
Brand: Spirent Pages: 22
Flexwatch FW3870 User Manual preview
FW3870
Brand: Flexwatch Pages: 13

Brands by name

Popular brands

Load more brands