Cisco Catalyst 4500 Series Installation Manual Download Page 45 | Manualshive

Page: 45 / 194

Cisco Catalyst 4500 Series Installation Manual Download Page 45

1-27

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Chapter 1 Product Overview

Supervisor Engines

LEDs

Table 1-6

describes the supervisor engine LEDs.

Gigabit Ethernet Uplink Ports

The Gigabit Ethernet uplink ports operate in full-duplex mode only. GBICs have
SC connectors to interface with multimode fiber (MMF) and single-mode fiber
(SMF) cable. For more information about GBICs, refer to the

Catalyst 4500

Series Module Installation Guide

.

Table 1-6

Supervisor Engine LEDs

LED

Color/State

Description

STATUS

Indicates the results of a series of self-tests:

Green

All diagnostic tests passed.

Red

A test failed.

Orange

System boot or diagnostic test is in progress.

Off

Module is disabled.

UTILIZATION

Green 1–100%

If the switch is operational, this display indicates the current
traffic load over the backplane (as an approximate percentage).

LINK

Indicates the status of the 10/100BASE-T port,
10/100/1000BASE-T or uplink ports:

Green

The link is operational.

Orange

The link is disabled by user.

Flashing orange

The power-on self-test indicates a faulty port.

Off

No signal is detected or there is a link configuration failure.

ACTIVE

Indicates whether the uplink port is active or not:

Green

The port is active.

Off

The port is not active.

ACTIVE

The LED to the right of the uplink ports is only used in switches
with two supervisors. The LED lights on the active supervisor.

«
...
43
44
45
46
47
...
»

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments