Cisco Catalyst 4500 Series Installation Manual Download Page 125

Page: 125 / 194

4-11

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Chapter 4 Removing and Replacing FRUs

Removing and Replacing the Power Supply

Removing a DC-Input Power Supply

This section describes how to remove a DC-input power supply.

Required Tools

You will need the following tools to perform this procedure:

•

A Phillips screwdriver

•

A 10-mm wrench/socket

Removal Procedure

Warning

Before performing any of the following procedures, ensure that power is
removed from the DC circuit.

Statement 1003

Follow these steps to remove a DC-input power supply:

Step 1

Turn off the in-line power switch. (Single input only. The triple-input power
supply does not have this switch.)

Step 2

Turn off the main power switch.

Step 3

Verify that power is off to the DC circuit on the power supply you are removing.

Step 4

Loosen the screw on the terminal block cover and remove it from the terminal
block (see

Figure 4-11

Figure 4-12

). The triple-input power supply has two

screws on the cover.

Summary of Contents for Catalyst 4500 Series



































































































































































































Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands

Cisco Catalyst 4500 Series, Installation Manual

Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands