manualshive.com logo in svg

Cisco Catalyst 4500 Series, Installation Manual, Page: 157 / 194

Share
Download
Cisco Catalyst 4500 Series Installation Manual Download Page 157

   

5-13

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Chapter 5      Troubleshooting

Troubleshooting Supervisor Engines

Troubleshooting Supervisor Engines

This section only addresses problems with hardware. Problems with features or 
configuration are not covered here. Refer for your software configuration guide 
and release notes for information on configuring features or identifying known 
problems.

Table 5-2

 describes the supervisor engine LEDs. Check the LEDs on your 

supervisor and compare them to the described LED behaviors.

Table 5-2

Supervisor Engine LEDs 

LED

Color/State

Description

STATUS 

Indicates the results of a series of self-tests.

Green

All diagnostic tests passed.

Red

A test failed.

Orange

System boot or diagnostic test is in 
progress.

Off

Module is disabled.

UTILIZATION Green 1–100%

If the switch is operational, this display 
indicates the current traffic load over the 
backplane (as an approximate percentage).

LINK

Indicates the status of the 10/100BASE-T 
Ethernet management port or uplink ports.

Green

The link is operational.

Orange

The link is disabled by user.

Flashing orange  The power-on self-test indicates a faulty 

port.

Off

No signal is detected or there is a link 
configuration failure.

Summary of Contents for Catalyst 4500 Series



































































































































































































Reviews:

No comments