Cisco Catalyst 4500 Series Installation Manual Download Page 9

Page: 9 / 194

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Preface

This preface describes the audience, organization, and conventions of the

Catalyst 4500 Series Switches Installation Guide

and provides information on

how to obtain related documentation and technical assistance.

Audience

Only trained and qualified service personnel (as defined in IEC 60950 and
AS/NZS3260) should install, replace, or service the equipment.

Organization

This guide is organized as follows:

Chapter

Title

Description

Chapter 1

Product Overview

Describes the hardware features, components, interfaces,
and functionality of the Catalyst 4500 series switches.

Chapter 2

Preparing for
Installation

Describes how to prepare your site for the installation of the
switch.

Chapter 3

Installing the Switch
in a Rack

Describes how to install the Catalyst 4500 series switches.
Provides procedures for removing and installing chassis
components.

Summary of Contents for Catalyst 4500 Series



































































































































































































Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands

Cisco Catalyst 4500 Series, Installation Manual

Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands