Cisco Catalyst 4500 Series Installation Manual Download Page 155

Page: 155 / 194

5-11

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Chapter 5 Troubleshooting

Troubleshooting Switching Modules

Figure 5-2

10/100BASE-T Port LEDs

17407

STATUS

WS-X4148-RJ

4 PORT
10/100 B

Table 5-1

Switching Module LEDs

LED

Color/State Description

STATUS

Indicates the results of a series of self-tests and
diagnostic tests performed by the switch.

Green

All the tests pass.

Red

A test other than an individual port test failed.

Orange

System boot, self-test diagnostics running, or the
module is disabled.

LINK

Used on the WS-X4232-L3 Ethernet routing module.

Indicates the status of the port.

Green

The port is operational (a signal is detected).

Orange

The link has been disabled by software.

Flashing
orange

The link has been disabled due to a hardware failure.

Off

No signal is detected.

Port
Status

LEDs labeled 1 through the number of ports on the switching module are the individual port link
LEDs.

Indicates individual port status.

Green

The port is operational (a signal is detected).

Orange

The link has been disabled by software.

Flashing
orange

The link has been disabled due to a hardware failure.

Off

No signal is detected.

Summary of Contents for Catalyst 4500 Series



































































































































































































Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands

Cisco Catalyst 4500 Series, Installation Manual

Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands