Cisco Catalyst 4500 Series Installation Manual Download Page 26

Page: 26 / 194

Chapter 1 Product Overview

Switch Features

1-8

Catalyst 4500 Series Switches Installation Guide

78-14409-08

Supervisor engine
support

•

Supports the Supervisor Engine II, II+, II+10GE, III, IV, V, 6-E

•

Holds the ASIC-based forwarding engine (data path) and the
management processor and software (control path)

•

Features interface monitoring, environmental status, and SNMP and
console/Telnet interface

Note

Packets are not forwarded while the module is removed; a system
reboot occurs when a supervisor engine is reinserted.

Switching module
support

•

24-port 10/100BASE-TX Fast Ethernet switching module
(WS-X4124-RJ45)

•

24-port 100BASE-FX Fast Ethernet switching module
(WS-X4124-FX-MT)

•

48-port 100BASE-FX Fast Ethernet switching module
(WS-X4148-FX-MT)

•

48-port 100BASE-LX10 Fast Ethernet switching module
(WS-X4148-FE-LX-MT)

•

48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ)

•

48-port 100BASE-BX10-D Fast Ethernet switching module
(WS-X4148-FE-BD-LC)

•

48-port 10/100-Mbps Fast Ethernet switching module
(WS-X4148-RJ21)

•

48-port Cisco pre-standard Power over Ethernet (PoE)
10/100BASE-TX switching module (WS-X4148-RJ45V)

•

24-port IEEE 802.3af-compliant PoE 10/100BASE-TX switching
module (WS-X4224-RJ45V)

•

48-port IEEE 802.3af compliant PoE 10/100BASE-TX RJ-45 switching
module (WS-X4248-RJ45V)

•

48-port 100BASE-X Fast Ethernet switching module
(WS-X4248-FE-SFP)

•

48 port IEEE 802.3af compliant PoE 10/100BASE-TX RJ-21 switching
module (WS-X4248-RJ21V)

Table 1-2

Features of the Catalyst 4506 Switch (continued)

Feature

Description

Summary of Contents for Catalyst 4500 Series



































































































































































































Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands

Cisco Catalyst 4500 Series, Installation Manual

Search results

Summary of Contents for Catalyst 4500 Series

Reviews:

Related manuals for Catalyst 4500 Series

Brands by name

Popular brands