manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 70 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 70

Symptom:

P0113-INTAKE AIR TEMPERATURE SENSOR HIGH

When Monitored and Set Condition:

P0113-INTAKE AIR TEMPERATURE SENSOR HIGH

When Monitored:

With the ignition on. Battery voltage greater than 10 volts.

Set Condition:

The Intake Air Temperature (IAT) sensor voltage at the PCM is greater

than 4.98 volts. One trip Fault.

POSSIBLE CAUSES

IAT SENSOR VOLTAGE ABOVE 4.6 VOLTS

(K21) IAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

IAT SENSOR INTERNAL FAILURE

(K21) IAT SIGNAL CIRCUIT OPEN

(K4) SENSOR GROUND CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, read the IAT Sensor voltage.

Is the voltage above 4.6 volts?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Ignition on, engine not running.
Measure the voltage of the (K21) IAT Signal circuit in the IAT Sensor harness
connector.
Is the voltage above 5.2 volts?

All

Yes

→

Repair the short to battery voltage in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

64

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments