manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 335 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 335

POWERTRAIN VERIFICATION TEST VER - 2 - NGC

APPLICABILITY

1. NOTE: After completing the Powertrain Verification Test the Transmission Verifi-
cation Test must be performed.
2. NOTE: If the PCM has been replaced and the correct VIN and mileage have not
been programmed, a DTC will be set in the ABS Module, Airbag Module and the
SKIM.
3. NOTE: If the vehicle is equipped with a Sentry Key Immobilizer System, Secret Key
data must be updated. Refer to the Service Information for the PCM, SKIM and the
Transponder (ignition key) for programming information.
4. Inspect the vehicle to ensure that all components related to the repair are connected properly.
5. With the DRBIII

t

, clear DTCs and Reset Memory all engine values.

6. Run the engine for one warm-up cycle to verify proper operation.
7. Road test the vehicle. Use all accessories that may be related to this repair.
8. With the DRBIII

t

, confirm that no DTC’s or Secondary Indicators are present and that all

components are functioning properly.
9. If this test is being performed after a No Trouble Code test, verify the symptom is no longer
present.
10. If the symptom is still present, or any other symptom or DTC is present refer to the
appropriate category and perform the corresponding symptom.
11. Refer to any Technical Service Bulletins that may apply.
12. If there are no DTCs present and all components are functional properly, the repair is
complete.
Are any DTCs present?

All

Yes

→

Repair is not complete, refer to appropriate symptom.

No

→

Repair is complete.

POWERTRAIN VERIFICATION TEST VER - 3 - NGC

APPLICABILITY

1. NOTE: After completing the Powertrain Verification Test the Transmission Verifi-
cation Test must be performed.
2. NOTE: If the PCM has been replaced and the correct VIN and mileage have not
been programmed, a DTC will be set in the ABS Module, Airbag Module and the
SKIM.
3. NOTE: If the vehicle is equipped with a Sentry Key Immobilizer System, Secret Key
data must be updated. Refer to the Service Information for the PCM, SKIM and the
Transponder (ignition key) for programming information.
4. Inspect the vehicle to ensure that all components related to the repair are connected properly.
5. With the DRBIII

t

, clear DTCs.

6. Perform generator output test. Refer to the appropriate service information as necessary.
7. Start the engine and set engine speed to 2000 RPM for at least thirty seconds.
8. Cycle the ignition key off and on.
9. With the DRBIII

t

, read the DTCs. If the DTC returns, or any other symptom or DTC is

present, refer to the appropriate category and perform the corresponding symptom.
10. If there are no DTCs present and all components are functioning properly, the repair is
complete.
Are any DTCs present?

All

Yes

→

Repair is not complete, refer to appropriate symptom.

No

→

Repair is complete.

329

VERIFICATION TESTS

Verification Tests —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments