manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 109 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 109

TEST

ACTION

APPLICABILITY

9

Ignition on, engine not running.
Disconnect the O2 Sensor harness connector.
With the DRBIII

t

, monitor the O2 Sensor voltage.

The O2 Sensor voltage should read 5.0 volts on the DRBIII

t

with the connector

disconnected.
Using a jumper wire, jump the O2 Signal circuit to the O2 Return circuit at the O2
Sensor harness connector.
NOTE: The voltage should drop from 5.0 volts to 2.5 volts with the jumper
wire in place.
Did the O2 Sensor volts change from 5.0 volts to 2.5 volts?

All

Yes

→

Replace the O2 Sensor
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

10

10

Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Ignition on, engine not running.
With the DRBIII

t

, monitor the O2 Sensor voltage.

Is the voltage above 4.8 volts?

All

Yes

→

Go To

11

No

→

Check the O2 Signal circuit for a short to ground, open, or short
to voltage. Inspect the O2 Sensor connector and the PCM harness
connector. If OK, replace and program the Powertrain Control
Module in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

11

Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the O2 Return circuit in the O2 Sensor harness connector.
Is the voltage at 2.5 volts?

All

Yes

→

Check the fuel system for contaminants. Also, check the exhaust
system for any leaks.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Check the O2 Return circuit for a short to ground, open, or short
to voltage. Inspect the O2 Sensor connector and the PCM harness
connector. If OK, replace and program the Powertrain Control
Module in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

103

DRIVEABILITY - NGC

P0171-FUEL SYSTEM 1/1 LEAN —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments