manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 123 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 123

TEST

ACTION

APPLICABILITY

11

Turn the ignition off.
Disconnect the Fuel Injector harness connector.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Check the Injector Control circuit.
Was a problem found with the Injector Control circuit?

All

Yes

→

Repair the Injector Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

NOTE: Before continuing, check the PCM harness connector
terminals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Control Module
in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

12

Turn the ignition off.
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Raise vehicle on hoist, and disconnect the fuel pressure line at the fuel pump module.
Install special 5/16 fuel line adapter tool #6539 between the disconnected fuel line
and the fuel pump module.
Attach a fuel pressure test gauge to the T fitting on the tool #6539
Ignition on, engine not running.
With the DRBIII

t

, actuate the ASD Fuel System test and observe the fuel pressure

gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Is the fuel pressure within specification?

All

Yes

→

Repair or replace fuel supply line as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

13

13

Turn the ignition off.
Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose,fitting or line, the fuel
system pressure must be released.
Remove the Fuel Pump Module and inspect the Fuel Inlet Strainer.
Is the Fuel Inlet Strainer plugged?

All

Yes

→

Replace the Fuel Pump Inlet Strainer.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

NOTE: Before continuing, check the Fuel Pump Module harness
connector terminals for corrosion, damage, or terminal push out.
Ensure the ground circuit is operating properly. Repair as neces-
sary. Replace the Fuel Pump Module.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

117

DRIVEABILITY - NGC

P0300-MULTIPLE CYLINDER MISFIRE —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments