manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 87 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 87

Symptom:

P0128-THERMOSTAT RATIONALITY

When Monitored and Set Condition:

P0128-THERMOSTAT RATIONALITY

When Monitored:

The engine running. During cold start.

Set Condition:

The PCM predicts a coolant temperature value that it will compare to the

actual coolant temperature. If the two coolant temperature values are not within 10°C
(50°F) of each other an error is detected. Two Trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

LOW COOLANT LEVEL

OTHER POSSIBLE CAUSES

SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

MONITOR ENGINE COOLANT TEMPERATURE

TEMPERATURE SENSOR VOLTAGE BELOW 1.0 VOLT

SIGNAL CIRCUIT OPEN

SENSOR GROUND CIRCUIT OPEN

SIGNAL CIRCUIT SHORTED TO GROUND

SIGNAL CIRCUIT SHORTED TO SENSOR GROUND

PCM LOW

PCM HIGH

TEST

ACTION

APPLICABILITY

1

NOTE: If any ECT, AAT, CMP or CKP sensor DTCs have set along with P0128,
diagnose them first before continuing.
NOTE: Ensure that Pinion Factor has been programmed correctly into the
PCM.
Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

81

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments