manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 81 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 81

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the TP Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K6) 5 Volt Supply circuit from the TP Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

9

No

→

Repair the open in the (K6) 5 Volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

9

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

10

Ignition on, engine not running.
With the DRBIII

t

, monitor the Throttle Position Sensor voltage.

Slowly open the throttle from the idle position to the wide open throttle position.
Does voltage start at approximately 0.7 of a volt and go above 3.5 volts with a smooth
transition?

All

Yes

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

75

DRIVEABILITY - NGC

P0122-THROTTLE POSITION SENSOR #1 LOW —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments