manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 219 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 219

Symptom:

P0533-A/C PRESSURE SENSOR HIGH

When Monitored and Set Condition:

P0533-A/C PRESSURE SENSOR HIGH

When Monitored:

The engine running. The A/C relay energized.

Set Condition:

The A/C pressure sensor signal at the PCM goes above 4.92 volts. One trip

Fault.

POSSIBLE CAUSES

A/C PRESSURE SENSOR VOLTAGE ABOVE 4.6 VOLTS

(C18) A/C PRESSURE SIGNAL CIRCUIT SHORTED TO (K7) 5 VOLT SUPPLY CIRCUIT

(C18) A/C PRESSURE SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

A/C PRESSURE SENSOR INTERNAL FAILURE

(C18) A/C PRESSURE SIGNAL CIRCUIT OPEN

(K4) SENSOR GROUND CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the A/C refrigerant System is properly charged per the
Service Information.
Start the engine.
With the DRBIII

t

, read the A/C Pressure Sensor voltage.

Is the voltage above 4.6 volts?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

2

Turn the ignition off.
Disconnect the A/C Pressure Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between the (C18) A/C Pressure Signal circuit and the (K7)
5 Volt Supply circuit in the A/C Pressure Sensor harness connector.
Is the resistance below 5.0 ohms?

All

Yes

→

Repair the (C18) A/C Pressure Signal circuit for a short to the (K7)
5 Volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

No

→

Go To

3

213

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments