manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 323 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 323

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Raise vehicle on hoist, and disconnect the fuel pressure line at the fuel pump module.
Install special 5/16 fuel line adapter tool #6539 between the disconnected fuel line
and the fuel tank module (passenger side).
Attach a fuel pressure test gauge tool #C-4799-B to the T fitting on the tool #6539
Turn the ignition on.
With the DRBIII

t

, actuate the ASD Fuel System test and observe the fuel pressure

gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Is the fuel pressure within specification now?

All

Yes

→

Repair/replace fuel supply line as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

Go To

6

Caution: Stop All Actuations.

6

Turn the ignition off.
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose,fitting or line,
the fuel system pressure must be released.
Gain access to the Fuel Pump Module (driver side) and the Fuel Tank Module
(passenger side).
Visually and Physically inspect the fuel line and siphon hose between the Fuel Pump
Module and the Fuel Tank Module. Look for disconnected and/or damage lines or
hoses.
Were the fuel line and the siphon hose in good condition?

All

Yes

→

Go To

7

No

→

Repair or Replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

7

NOTE: Before continuing inspect the Fuel Pressure Regulator. Ensure the
Fuel Pressure Regulator is properly install in the Fuel Tank Module.
Remove the Fuel Tank Module (passenger side).
Replace the Fuel Pressure Regulator.
Install the Fuel Pump Module and the Fuel Tank Module in accordance with the
service manual.
Using a fuel pressure gauge, check the fuel pressure.
NOTE: Fuel pressure specification is 400 kPa +/- 34 kPa (58 psi +/- 5 psi).
Is the fuel pressure within specification?

All

Yes

→

Test Complete.

No

→

Replace the Fuel Pump Module.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

317

STARTING

*ENGINE CRANKS DOES NOT START —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments