manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 303 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 303

Symptom:

*CHECKING THE A/C RELAY OUTPUT

POSSIBLE CAUSES

A/C CLUTCH RELAY OPERATION

GROUND CIRCUIT OPEN

A/C CLUTCH

(A17) FUSED B+ CIRCUIT

(C3) A/C CLUTCH OUTPUT CIRCUIT

A/C CLUTCH RELAY

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure that the refrigerant system is properly charged. Refer to the
appropriate Service Information.
Turn the ignition on.
With the DRBIII

t

, actuate the A/C Clutch Relay.

Is the A/C Clutch actuating?

All

Yes

→

The A/C Clutch System operating properly at this time.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

No

→

Go To

2

2

Turn the ignition off.
Disconnect the A/C Clutch harness connector.
Measure the Ground circuit in the A/C Clutch harness connector to ground.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

3

No

→

Repair the Ground circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

3

Disconnect the A/C Clutch harness connector.
Turn the ignition on.
With the DRBIII

t

, actuate the A/C Clutch Relay.

Measure the voltage of the A/C Clutch Relay Output circuit in the A/C Clutch harness
connector.
Is the voltage above 11.0 volts?

All

Yes

→

Replace the A/C Clutch.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

No

→

Go To

4

4

Turn the ignition off.
Remove the A/C Clutch Relay from the PDC.
Using a 12-volt test light connected to ground, probe the (A17) Fused B+ circuit in the
PDC.
Does the test light illuminate brightly?

All

Yes

→

Go To

5

No

→

Repair the (A17) Fused B+ circuit. Inspect fuses and replace as
necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

297

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments