manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 104 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 104

TEST

ACTION

APPLICABILITY

2

Turn the ignition off.
NOTE: Allow the O2 Sensor to cool down before continuing the test. The O2
voltage should stabilize at 5.0 volts. Raising the hood may help in reducing
under hood temps.
Ignition on, engine not running.
With the DRBIII

t

, actuate the O2 Heater Test.

With the DRBIII

t

, monitor O2 Sensor voltage for at least 2 minutes.

Does the voltage stay above 4.5 volts?

All

Yes

→

Go To

3

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

3

NOTE: Allow the O2 sensor to cool down to room temperature.
Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Measure the resistance across the O2 Sensor Heater element component side.
NOTE: O2 Sensor Heater Resistance Specification: 1/1 and 1/2 O2 Sensor 2.1
to 2.7 ohms.
Is the resistance within the specifications?

All

Yes

→

Go To

4

No

→

Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

4

Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Measure the resistance between an engine ground and the O2 Heater Ground circuit
in the O2 Sensor harness connector.
Is the resistance below 0.5 of an ohm?

All

Yes

→

Go To

5

No

→

Repair the open/high resistance in the O2 Heater Ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

5

Turn the ignition off.
Disconnect the O2 Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the O2 Heater Control circuit from the O2 Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 0.5 of an ohm?

All

Yes

→

Go To

6

No

→

Repair the open/high resistance in the O2 Heater Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

98

DRIVEABILITY - NGC

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments