manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 213 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 213

Symptom:

P0517-BATTERY TEMPERATURE SENSOR HIGH

When Monitored and Set Condition:

P0517-BATTERY TEMPERATURE SENSOR HIGH

When Monitored:

Ignition on.

Set Condition:

Battery temperature voltage above 4.8 volts.

POSSIBLE CAUSES

BATTERY TEMP VOLTAGE ABOVE 4.8 VOLTS

BATTERY TEMP SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

BATTERY TEMP SENSOR INTERNAL FAILURE

BATTERY TEMP SIGNAL CIRCUIT OPEN

SENSOR GROUND CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, read the Battery Temp Sensor voltage.

Is the voltage above 4.8 volts?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the Battery Temp Sensor harness connector.
Ignition on, engine not running.
Measure the voltage of the Battery Temp Signal circuit in the Battery Temp Sensor
harness connector.
Is the voltage above 5.2 volts?

All

Yes

→

Repair the short to battery voltage in the Battery Temp Signal
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

207

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments