manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 103 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 103

Symptom List:

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE
P0141-O2 SENSOR 1/2 HEATER PERFORMANCE

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0135-O2 SENSOR 1/1 HEATER
PERFORMANCE.

When Monitored and Set Condition:

P0135-O2 SENSOR 1/1 HEATER PERFORMANCE

When Monitored:

Engine Running and Heater duty cycle greater than 0%

Set Condition:

O2 Heater Temperature does not reach 575°C (959°F) within 90 second

during monitoring conditions. Two Trip Fault.

P0141-O2 SENSOR 1/2 HEATER PERFORMANCE

When Monitored:

Engine Running and Heater duty cycle greater than 0%.

Set Condition:

O2 Heater Temperature does not reach 575°C (959°F) within 45 second

during monitoring conditions. Two Trip Fault.

POSSIBLE CAUSES

O2 SENSOR HEATER OPERATION

O2 HEATER ELEMENT

O2 HEATER GROUND CIRCUIT OPEN

O2 HEATER CONTROL CIRCUIT OPEN

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter display and equal to zero?

All

Yes

→

Go To

3

No

→

Go To

2

97

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments