manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 252 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 252

Symptom:

P0660-MANIFOLD TUNE VALVE SOLENOID CIRCUIT

When Monitored and Set Condition:

P0660-MANIFOLD TUNE VALVE SOLENOID CIRCUIT

When Monitored:

With the ignition on. ASD Relay energized. Battery voltage greater

than 10 volts.

Set Condition:

The PCM senses the MTV is not at the desired state. One Trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

GROUND CIRCUIT OPEN

MTV RELAY OUTPUT CIRCUIT OPEN

FUSED B+ CIRCUIT

MTV RELAY CONTROL CIRCUIT SHORTED TO GROUND

MTV RELAY GROUND CIRCUIT

MTV RELAY

MTV RELAY CONTROL CIRCUIT OPEN

MANIFOLD TUNING VALVE SLOENOID

PCM

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t

, read DTC’s.

Is the Good Trip displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the Manifold Tune Valve Solenoid harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the MTV Relay Output circuit
in the MTV Solenoid harness connector.
With the DRBIII

t

, actuate the MTV Relay.

Does the 12-volt test light illuminate brightly?

All

No

→

Go To

3

Yes

→

Go To

10

246

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments