Home
/
Chrysler
/
Pacifica CS 2004
/
Service Manual

Chrysler Pacifica CS 2004, Service Manual, Page: 173 / 370

Share

Page: 173 / 370

Chrysler Pacifica CS 2004 Service Manual Download Page 173

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Carefully inspect the Evap Purge Solenoid vacuum supply hose for proper routing.
Check for a pinched or plugged hose from the throttle body to the Purge Solenoid.
Inspect the vacuum port at the throttle body for any damage or plugging.
Were any problems found?

All

Yes

→

Repair the vacuum supply hose/tube as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

167

DRIVEABILITY - NGC

P0441-EVAP PURGE SYSTEM PERFORMANCE —

Continued

«
...
171
172
173
174
175
...
»

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments