manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 172 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 172

Symptom:

P0441-EVAP PURGE SYSTEM PERFORMANCE

When Monitored and Set Condition:

P0441-EVAP PURGE SYSTEM PERFORMANCE

When Monitored:

Cold start test. Engine Running. Small Leak Test Passed.

Set Condition:

The PCM activates the EVAP Purge solenoid gradually increases to

maximum flow. During flow, the PCM looks for the NVLD switch to close. If the PCM does
not see the NVLD switch close at maximum flow an error is detected. Two Trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

INTERMITTENT CONDITION

CHECKING EVAP PURGE SOLENOID FUNCTIONALITY

EVAP PURGE SOLENOID VACUUM SUPPLY

TEST

ACTION

APPLICABILITY

1

NOTE: If any of the following DTCs are set (P0443, P0452, P0453, P0498 or
P0499) diagnose them first before continuing with P0441.
Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

NOTE: After disconnecting the Evap Purge vacuum connections, inspect
the lines and solenoid for any signs of contamination or foreign materials.
Using a hand vacuum pump, apply 10 in Hg to

9

CAN

9

side of the EVAP Purge

Solenoid.
Ignition on, engine not running.
Observe the vacuum gauge.
With the DRBIII

t

, actuate the EVAP Purge Solenoid .

Does the vacuum drop when the solenoid is actuated?

All

Yes

→

Go To

3

No

→

Replace the Evap Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

166

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments