manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 242 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 242

Symptom List:

P0600-SERIAL COMMUNICATION LINK
P0601-INTERNAL MEMORY CHECKSUM INVALID

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0600-SERIAL COMMUNICA-
TION LINK.

When Monitored and Set Condition:

P0600-SERIAL COMMUNICATION LINK

When Monitored:

With the ignition on.

Set Condition:

Internal Bus communication failure between the Engine and Transmis-

sion processors.

P0601-INTERNAL MEMORY CHECKSUM INVALID

When Monitored:

With the ignition on.

Set Condition:

Internal checksum for software failed, does not match calculated value.

POSSIBLE CAUSES

PCM INTERNAL OR SPI

TEST

ACTION

APPLICABILITY

1

The Powertrain Control Module is reporting internal errors, view repair to continue.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

236

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments