manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 192 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 192

Symptom List:

P0462-FUEL LEVEL SENSOR #1 LOW
P0463-FUEL LEVEL SENSOR #1 HIGH
P2067-FUEL LEVEL SENSOR #2 LOW
P2068-FUEL LEVEL SENSOR #2 HIGH

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0462-FUEL LEVEL SENSOR #1
LOW.

When Monitored and Set Condition:

P0462-FUEL LEVEL SENSOR #1 LOW

When Monitored:

Ignition on and battery voltage above 10.4 volts.

Set Condition:

The fuel level sensor signal voltage goes below 0.1961 volts for more than

5 seconds. One Trip Fault.

P0463-FUEL LEVEL SENSOR #1 HIGH

When Monitored:

Ignition on and battery voltage above 10.4 volts.

Set Condition:

The fuel level sensor signal voltage at the PCM goes above 4.7 volts for

more than 5 seconds. One Trip Fault.

P2067-FUEL LEVEL SENSOR #2 LOW

When Monitored:

Ignition on and battery voltage above 10.4 volts.

Set Condition:

The fuel level sensor signal voltage goes below 0.1961 volts for more than

5 seconds. One Trip Fault.

P2068-FUEL LEVEL SENSOR #2 HIGH

When Monitored:

Ignition on and battery voltage above 10.4 volts.

Set Condition:

The fuel level sensor signal voltage at the PCM goes above 4.7 volts for

more than 5 seconds. One Trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

INTERMITTENT CONDITION

186

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments