manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 215 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 215

Symptom:

P0522 PRESSURE SENSOR LOW

When Monitored and Set Condition:

P0522 PRESSURE SENSOR LOW

When Monitored:

Engine running and battery voltage above 10.4 volts.

Set Condition:

The oil pressure sensor voltage at PCM goes below 0.1 of a volt for 0.5 of

a second.

POSSIBLE CAUSES

OIL PRESSURE SENSOR VOLTAGE BELOW 0.1 VOLTS

OIL PRESSURE SENSOR INTERNAL FAILURE

(G6) OIL PRESS SIGNAL SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the engine oil pressure is at the correct pressure before
continuing.
Ignition on, engine not running.
With the DRBIII

t

, read the Oil Pressure Sensor voltage.

Is the voltage below 0.1 volt?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the Oil Pressure Sensor harness connector.
Ignition on, engine not running.
With the DRBIII

t

, read Oil Pressure Sensor voltage.

Does the Oil Pressure Sensor voltage read approximately 5.0 volts?

All

Yes

→

Replace the Oil Pressure Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

3

Turn the ignition off.
Disconnect the Oil Pressure Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (G6) Oil Press Signal circuit in the
Oil Pressure Sensor harness connector.
Is the resistance below 100 ohms?

All

Yes

→

Repair the ground shorted to the (G6) Oil Press Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

209

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments