manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 37 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 37

Symptom:

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT

When Monitored and Set Condition:

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT

When Monitored:

Engine cranking and Engine running

Set Condition:

Powertrain Control Module detects an error when the camshaft position is

out of phase with the crankshaft position. One trip fault.

POSSIBLE CAUSES

INTERMITTENT CONDITION

CHECKING INTERMITTENT CMP SIGNAL WITH LAB

CMP WIRE HARNESS INSPECTION

TONE WHEEL/PULSE RING INSPECTION

CKP WIRE HARNESS INSPECTION

TONE WHEEL/PULSE RING INSPECTION

INTERMITTENT CKP SIGNAL

CAMSHAFT POSITION SENSOR

CRANKSHAFT POSITION SENSOR

TEST

ACTION

APPLICABILITY

1

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

With the DRBIII

t

, erase DTCs.

Start the engine and run until operating temp is reached. (Closed Loop)
If the DTC does not reset it may be necessary to take the vehicle on a test drive.
Does the DTC reset?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

31

DRIVEABILITY - NGC

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments