manualshive.com logo in svg

Chrysler Pacifica CS 2004, Service Manual, Page: 71 / 370

Share
Download
Chrysler Pacifica CS 2004 Service Manual Download Page 71

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the IAT harness connector.
Connect a jumper wire between the (K21) IAT Signal circuit and the (K4) Sensor
ground circuit in the IAT harness connector.
Ignition on, engine not running.
With the DRBIII

t

, read IAT voltage.

Is the voltage below 1.0 volt?

All

Yes

→

Replace the IAT Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

4

4

Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K21) IAT Signal circuit from the IAT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

5

No

→

Repair the open in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

5

Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K4) Sensor ground circuit from the IAT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

6

No

→

Repair the open in the (K4) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

6

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

65

DRIVEABILITY - NGC

P0113-INTAKE AIR TEMPERATURE SENSOR HIGH —

Continued

Summary of Contents for Pacifica CS 2004



















































































































































































































































































































































































Reviews:

No comments