manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Troubleshooting Manual, Page: 7 / 200

Share
Download
Canon imageRUNNER ADVANCE C3330 Series Troubleshooting Manual Download Page 7

If the symptom has not improved sufficiently, fine-tune the setting values in the steps a-1)

b) Extend the range where trail edge weak bias is applied.
b-1) Increase the setting value of Service mode (Lv2) > Mode List > COPIER > Adjust > HV-TR > [B2TR-LNG].
Change of the adjustment value by "1" extends the range where trail edge weak bias is applied 0.1mm.
The range of setting is from "-100" to "+100" ("0" by default).
[Caution] The change of this setting that lowers the secondary transfer voltage of the paper trailing edge part (the range of
correction amount) of all the output sheets may result in a mottling image with a high density image.
b-2) Output the image having shown the symptom, and check that the symptom does not occur.
If the symptom has not improved sufficiently, fine-tune the setting values in the steps b-1)

c) Lower the secondary transfer voltage applied to trailing edge with customized settings
The secondary transfer voltage setting works only when all the conditions (mode/environment/paper type) registered beforehand
are met.
16 different patterns are registerable by registering the settings to each "TR-DUP1" to "TR-DUP16".
The below procedure is to set "TR-DUP1".
c-1) Go toService mode (Level 2) > Mode List > COPIER > Adjust > HV-TR > and change the setting value of "TR-DUP1".
- If the symptom occurs in 1-sided mode, change the value to "41".
- If the symptom occurs on the second side in auto 2-sided mode, change the value to "42".
- If the symptom occurs on the second side in multi-purpose tray 2-sided mode, change the value to "43".
The range of setting is from "11" to "43" ("11" by default).
c-2) Go to Service mode (Level 2) > Mode List > COPIER > Adjust > HV-TR > and confirm if the setting value of "TR-ENV1" is
set to "1".
The range of setting is from "1" to "3" ("1" by default).
c-3) Choose the appropriate value from among the below tables according to the used paper type and apply it to the setting value
of Service mode (Level 2) > Mode List > COPIER > Adjust > HV-TR > "TR-PPR1".
The range of setting is from "1" to "25" ("1" by default).

c-4) Go to Service mode (Level 2) > Mode List > COPIER > Adjust > HV-TR > and change the setting value of "TR-VL1" to "-5".
The range of setting is from "-128" to "+127" ("0" by default).
Change the setting value by "1" changes the secondary transfer voltage 30V.
[Caution] The secondary transfer voltage of the paper trailing edge part is lowered and a mottling image may occur with a high
density image.
c-5) Output the image having shown the symptom, and check that the symptom does not occur.
If the symptom does not improve sufficiently, reduce the setting value in the step c-4) by "5" at a time down to "-30" until the
symptom improves enough.

2

Summary of Contents for imageRUNNER ADVANCE C3330 Series









































































































































































































Reviews:

No comments