manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Troubleshooting Manual, Page: 21 / 200

Share
Download
Canon imageRUNNER ADVANCE C3330 Series Troubleshooting Manual Download Page 21

4) If lines appear on an image, Select Settings/Registration > Adjustment/Maintenance > Maintenance > Clean Inside Main unit
[1],and press "Start" button [2].

[Reference] T he cleaning takes about 80 sec.
5) If Margin displacement occurs on the leading edge/ left edge, adjust the margin on the leading edge/ left edge by referring to
"Adjustment > Pickup Feed System > Image position adjustment" described in Service manual.
6) Output the image having shown the symptom, and check that the symptom does not occur.

[Caution] When the host machine has to be moved to another place after installation, carry it out referring to " Installation > When
moving the host machine to another place after installation, execute the operation shown below." in Service manual.
If the host machine is moved without referring it, it may lead to breakage of parts/faulty images.

16

Summary of Contents for imageRUNNER ADVANCE C3330 Series









































































































































































































Reviews:

No comments