manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Troubleshooting Manual, Page: 101 / 200

Share
Download
Canon imageRUNNER ADVANCE C3330 Series Troubleshooting Manual Download Page 101

Copier Color | iR-ADV C3330/C3325/C3320 Series |
Copier Color | iR-ADV C3530/C3525/C3520 Series |
Copier Color | iR-ADV C5560/C5550/C5540/C5535 Series |

Measures when paper is not stapled (corner/double) after
installation (Inner Finisher-G1/H1/K1)

[Symptom]

In operation of stapling (corner/double) after installation of Inner Finisher, paper may not be stapled.

[Cause]

When installing Inner Finisher, distortion may occur in Inner Finisher.
If the center return belt guide [1] on the front side slips into the edge of the assist unit sheet metal [2] due to this distortion, paper
in staple operation is caught on by the center return belt guide and is not fed up to the stapling position, resulting in the above-
mentioned symptom.

[Service work]

If the above-mentioned symptom occurs, remove the center return belt guide from slipping into state.
1) Insert approx. 20 sheets of A4 or LTR-size plain paper [1] through the delivery outlet [2] of Inner Finisher up to position [a] in
the arrow direction.

[Reference] If the paper retainer [1] blocks the delivery outlet, move the paper retainer in the arrow direction manually.

96

Summary of Contents for imageRUNNER ADVANCE C3330 Series









































































































































































































Reviews:

No comments