manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Troubleshooting Manual, Page: 28 / 200

Share
Download
Canon imageRUNNER ADVANCE C3330 Series Troubleshooting Manual Download Page 28

3) Open the Front Door, and remove the Front Door [1] while lifting it up slightly and pushing the claw [2].
- 1 Claw [2]
- 2 Bosses [3]

4) Remove the Drum Unit (Bk).
[Caution]
- If you perform the work while in sleep mode or when the power was turned OFF while in sleep mode, the Primary Transfer Roller
will not be disengaged.
When removing the Drum Unit (Bk), be sure to do so after returning the machine to a standby state.
- Since there is a risk of damaging the Photosensitive Drum, do not touch the surface.
- Be sure to block light to the removed Drum Unit using paper, otherwise it will be exposed to light.
5) Remove the Control Panel Lower Cover [1].
- 2 Screws [2]
- 2 Claws [3]

6) Remove the Delivery Outlet Side Cover [1].
- 1 Screw [2]

23

Summary of Contents for imageRUNNER ADVANCE C3330 Series









































































































































































































Reviews:

No comments