manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Troubleshooting Manual, Page: 44 / 200

Share
Download
Canon imageRUNNER ADVANCE C3330 Series Troubleshooting Manual Download Page 44

-Recycled paper 1 (64 to 75 gsm): IMG-FIX > Change "TMP-TB11".
-Recycled paper 2 (76 to 90 gsm): IMG-FIX > Change "TMP-TB13".
The range of setting is from "-2" to "+2" ("0" by default).
Change of the setting value by "1" lowers the fixing control temperature 5 degrees Celsius, so that the curl is reduced.
[Reference] If the symptom occurs with a thin paper (52 to 63 gsm), handle the issue by referring to FAQ "The marks caused by
friction/Wrinkles on the second side of the paper of duplex printing due to using thin paper".
3) Output the image having shown the symptom, and check that the symptom does not occur.
If the symptom does not improve sufficiently, then change the setting value in the step 2) to "-2".
[Caution] Change of the setting lowers the fixing control temperature and poor fixing may occur.
4) Output the image having shown the symptom, and check that the symptom does not occur.

39

Summary of Contents for imageRUNNER ADVANCE C3330 Series









































































































































































































Reviews:

No comments