Canon CLBP-460PS Service Manual Download Page 296 | Manualshive

Page: 296 / 566

background image

replace the upper thermistor.

2) Abnormal lower thermistor

Action:

Turn the power switch OFF and remove the fixing unit. Measure the resistance
between the fixing unit connector J82-A4 (THRL) and J82-A3 (GND). If it is not
between 430k

Ω

to 310k

Ω

(room temperature 25°C), check the wire between the fix-

ing unit connector J82 and the lower thermistor connector J85. If it is normal,
replace the lower thermistor.

3) Defective power supply unit

Action:

Replace the power supply unit.

4) Defective DC controller PCB

Action:

Replace the DC controller PCB.

[ 6-13 ] “SERVICE CALL NOTE # D6” Fixing unit malfunction (broken heater wire)
<Possible causes>

1) Upper fixing heater wire/upper thermoswitch wire is broken

Action:

Remove the fixing unit from the printer. If there is no continuity between the fixing
unit connector J82-2 (HTH) and J82-3 (HTUC), check the upper fixing heater and
the upper thermoswitch, and replace the defective parts.

2) Lower fixing heater wire/lower thermoswitch wire is broken

Action:

Remove the fixing unit from the printer. If there is no continuity between the fixing
unit connector J82-2 (HTH) and J82-4 (HTLC), check the lower fixing heater and the
lower thermoswitch, and replace the defective parts.

3) Poor contact in connectors

Action:

Reconnect the DC controller PCB connector J1012 and the fixing unit connector
J82, and the power supply unit connectors J1 and J2 correctly.

4) Defective power supply unit

Action:

Replace the power supply unit.

5) Defective DC controller PCB

Action:

Replace the DC controller PCB.

[ 6-14 ] “SERVICE CALL NOTE # E1” Developing rotary malfunction
<Possible causes>

1) Claw for releasing developing rotary break is damaged

Action:

Check the claw on the cartridge door for releasing developing rotary break. Replace
the cartridge door if the claw is damaged.

2) Open the cartridge door and turn the power switch ON while holding down the developing

rotary break release lever and the door switch. If the developing rotary does not rotate, go
to step 9).

3) Damaged rotary drive unit

Action:

Replace any drive gears in the rotary drive unit if damaged or worn.

4) Damaged developing rotary position sensor flag

4 - 42

CHAPTER 4

«
...
294
295
296
297
298
...
»

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CLBP-460PS

Brand: D-Link Pages: 12

Brand: Ier Pages: 8

Brand: Xerox Pages: 25

Brand: 3D Systems Pages: 26

Brand: 3D Systems Pages: 39

WorkSeries 200 Series

Brand: 3D Platform Pages: 9

Brand: G3D Pages: 4

Brand: Olympus Pages: 2

Brand: Olympus Pages: 148

Brand: Xerox Pages: 262

Brand: Cashino Pages: 74

Brand: Zonestar Pages: 25

Brand: Konica Minolta Pages: 15

FELIX Pro 3 Touch

Brand: Felix printers Pages: 29

Brand: Lexmark Pages: 13

8560MFPD - Phaser Multifunction Printer Color Laser

Brand: Xerox Pages: 20

Brand: SPRT Pages: 14

Brand: VASTEX Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands