Canon CLBP-460PS Service Manual Download Page 154 | Manualshive

Page: 154 / 566

background image

D. Boot ROM menu

To execute the Boot ROM menu, press the MENU and CANCEL keys until the online LED and
error LED go OFF when turning ON the power.

The following functions can be executed from the menu.

• VERSION INFO: Displays version information.
• INSTALL UPGRADE: Installs software to upgrade.
• FORMAT DISK: Formats the hard disk drive
• CHANGE ENET MAC: Changes Ethernet MAC address.
• CHANGE DEFAULT LOCATE: Changes the destination flag.
• CLEAR NVRAM: Clears the parameters in the video controller EEPROM (NVRAM).

Each function is explained below. See Figure 2-6-5 for panel operation of each function.

1. VERSION INFO

Version information, version number and release date of the Boot Strap, Boot Code and System
Code are displayed. In some cases, the Boot Strap version and Boot Code version are different.

2. INSTALL UPGRADE

Upgrades the Boot ROM, System Code and File System. Any system software can be upgraded
via the parallel port if the Flash DIMM is installed.

3. FORMAT DISK

Executes high level format (creates file system on the hard disk) and low level format of the hard
disk drive. However, this cannot be executed if the hard disk drive is not installed on the video
controller.

4. CHANGE ENET MAC

Changes the Ethernet MAC address. This cannot be executed if the MAC address is locked. A
jumper must be attached to J25 pin on the video controller PCB before changing the MAC
address.

5. CHANGE DEFAULT LOCATE

Changes the destination flag. Default paper size (A4 or LETTER) is determined by this. A
jumper must be attached to J25 pin on the video controller PCB to change the flag.

6. CLEAR NVRAM PARAMETERS

Clears the items stored within the Boot ROM in the video controller EEPROM (NVRAM) that can
be changed by the user.

2 - 96

CHAPTER 2

«
...
152
153
154
155
156
...
»

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CLBP-460PS

Brand: Nantian Electronics Pages: 4

Brand: idp Pages: 88

Brand: Xerox Pages: 11

Brand: Xerox Pages: 30

Versant 4100 Press

Brand: Xerox Pages: 68

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 2

Versant 2100 Press

Brand: Xerox Pages: 68

Brand: Canon Pages: 2

Brand: Oki Pages: 20

Brand: Oki Pages: 320

Brand: DNP Pages: 66

Brand: Aficio Pages: 156

Brand: Rimage Pages: 217

IM C6000 Series

Brand: Ricoh Pages: 2

Brand: Xerox Pages: 4

Brand: Ricoh Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands