manualshive.com logo in svg

Canon CLBP-460PS, Service Manual

Share
Download
Canon CLBP-460PS Service Manual Download Page 177

3) Unhook the 2 claws at the bottom of the

drum cartridge drawer, and then
remove the upper front cover unit.

➀ 

Claws

➁ 

Upper front cover

Figure 3-2-10

Note:

When putting the upper front cover
back to the drum cartridge drawer,
confirm that the pin of the grip cam
is inserted to the groove of the
drawer lock lever properly.

Figure 3-2-11

7. Lower front cover unit

1) Open the ITB unit drawer.
2) Unhook the 2 Claws and remove the 2

screw covers.

➀ 

Claws

➁ 

Screw covers

Figure 3-2-12

3) Remove the 2 screws and pull the lower

front cover unit toward you to remove
the boss.

➀ 

Screws

➁ 

Lower front cover

Figure 3-2-13

4) Move the lower front cover unit down-

ward to remove.

3 - 7

CHAPTER 3

➀

➁

Drum cartride drawer unit

Upper front cover unit

Grip cam

Drawer lock lever

Pin

➀

➁

➁

➀

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands