manualshive.com logo in svg

Canon CLBP-460PS, Service Manual

Share
Download
Canon CLBP-460PS Service Manual Download Page 149

g. Flash ROM (U10)

The Flash ROM has a memory capacity of 1MB and stores self test program which is executed
while booting up the system.

h. AIR (U52)

The AIR is used for processing data which is sent to the video interface.  Smoothing is processed
in the AIR.

i.

EEPROM (U53)

The EEPROM has a memory capacity of 32KB which is capable of clearing electrically stored
data and writing new data.  It is used for storage of persistent printer parameters, such as print
environment and number of prints, that must be maintained across power cycles.  

• Video controller location

Figure 2-6-1

2 - 91

CHAPTER 2

CPU

(U35)

RAM DIMM

Memory

ASIC

(U4)

Video
ASIC

(U7)

J14

J2

J12

J4

J15

RAM DIMM

RAM DIMM

ROM DIMM

J8

J7

J6

J5

I/O ASIC

(U3)

AIR

Ethernet
control

FIFO

SRAM SRAM

SRAM

EEPROM

(U53)

Flash ROM

(U10)

(U52)

J1

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands