Canon CLBP-460PS Service Manual Download Page 152 | Manualshive

Page: 152 / 566

background image

C. Self Test

The printer has a function that executes the self diagnostics program stored in the video con-
troller when the power is turned ON to check the state of the video controller and control panel.
This function is called self test.

Normally, when the power is turned ON, START SELF-TEST appears in the message area and

the POWER-UP diagnostic set is run after the CPU initialization completes. If you hold down the
up arrow key at this time, you can select other diagnostic set. DIAGNOSTIC SETS appears in
the message area when the printer enters the mode which allows you to select a diagnostic set.

The available diagnostic sets in the self test selection screen are as follows.

• CUSTOM diagnostic set
• FUNCTIONAL diagnostic set
• BURN-IN diagnostic set
• START-UP diagnostic set

Use the up and down keys to select a diagnostic set and press the Enter key to run the set. If
you press the MENU key, the START-UP diagnostic set is run regardless of the selected diag-
nostic set.

Each of the diagnostic sets will be explained in the following sections. See figure 2-6-4 for

the panel operation of each menu.

1. POWER-UP diagnostic set

The POWER-UP diagnostic set checks the following items every time the power is turned ON.

• DIMM slot
• Video ASIC (U7)
• ROM
• Built in flash ROM
• Ethernet controller chip
• Token Ring card (option)
• Display window
• Hard disk drive (option)

When this diagnostic set is completed, the printer enters Standby, and “READY” appears in the
message area. If an operator call or error has occurred, it is indicated in the status display
panel.

2. CUSTOM diagnostic set

If the CUSTOM diagnostic set is selected, the tests executed in the POWER-UP diagnostic set can
be executed individually in more detail. The user will be presented with a series of menus which
allow the user to specify which tests should be run and how to stop the tests.

3. FUNCTIONAL diagnostic set

If the FUNCTIONAL diagnostic set is selected, a more comprehensive set of tests is run, which
are usually used by manufacturing. As the tests require special tools, this set cannot be run in
the field.

4. BURN-IN diagnostic set

If the BURN-IN diagnostic set is selected, a set of tests is executed repeatedly to exercise board
functions.

2 - 94

CHAPTER 2

«
...
150
151
152
153
154
...
»

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CLBP-460PS

Brand: NCR Pages: 10

Brand: Xerox Pages: 310

Brand: Lanier Pages: 265

Magicolor 2 Desklaser

Brand: QMS Pages: 60

Panafax UF-9000

Brand: Panasonic Pages: 375

imageRUNNER ADVANCE C3330 Series

Brand: Canon Pages: 5

imagePROGRAF TA-30

Brand: Canon Pages: 49

Brand: Canon Pages: 210

Color imageCLASS MF8180c

Brand: Canon Pages: 34

Donation Point Even

Brand: Quest Payment Systems Pages: 2

Brand: Oki Pages: 336

Brand: AstroJet Pages: 32

Brand: CNET Pages: 2

Brand: Kyocera Pages: 16

16A0310 - OptraImage 242

Brand: Lexmark Pages: 207

Brand: Hitachi Pages: 11

Brand: Hitachi Pages: 62

Brand: Hitachi Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands