Canon CLBP-460PS Service Manual Download Page 175

Page: 175 / 566

B. External Covers
1. Top cover unit

1) Remove the control panel according to

the control panel removal procedures
on Page 3-9.

2) Open the rear cover.
3) Remove the 2 screws.

➀

Screws

Figure 3-2-2

4) Open the top cover and drum cartridge

drawer.

5) Unhook the 6 claws. Lift up the top

cover unit in the direction of the arrow
to unhook the 2 hooks and then remove
the unit.

➀

Claws

➁

Hooks

➂

Upper cover unit

Figure 3-2-3

2. Left cover unit

1) Remove the top cover unit.
2) Remove the cassette.
3) Open the ITB unit drawer.
4) Remove the 2 screws and unhook the

claw.

5) Lift up the left cover in the direction of

the arrow and unhook the 2 hooks to
remove the cover.

➀

Screws

➁

Claw

➂

Hooks

➃

Left cover unit

Figure 3-2-4

3. Right cover

1) Remove the top cover unit.
2) Remove the 2 screws.
3) Lift up the right cover in the direction of

the arrow and unhook the 3 hooks to
remove the cover.

➀

Screws

➁

Right cover unit

➂

Hooks

Figure 3-2-5

3 - 5

CHAPTER 3

➀

➂

➀

➁

➃

➁

➂

➀

➁

➂

➀

Summary of Contents for CLBP-460PS






















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CLBP-460PS

Reviews:

Brands by name

Popular brands

Canon CLBP-460PS, Service Manual

Search results

Summary of Contents for CLBP-460PS

Reviews:

Brands by name

Popular brands