manualshive.com logo in svg

Canon CLBP-460PS, Service Manual

Share
Download
Canon CLBP-460PS Service Manual Download Page 182

< Notes for reassembly >

When the drum drive unit has been disassembled, reassemble the gears as shown in figure 3-
3-8.
When installing the gears 27T and 28T, adjust their positions according to the procedures
described in figure 3-3-9.
When replacing the gears in the figure below, apply grease to the gears and shafts to prevent
noise.  Type of grease and application method are described below.  Do not use grease other than
the ones specified here.

Lubricating material:HY9-0007

Apply to the gears according to the instructions in the figure below.

Lubricating oil:CK-8003

Apply a drop to the shafts and side contact surface of the gears specified in the figure below.

Figure 3-3-8

3 - 12

CHAPTER 3

Apply 0.05g of lubricating material to the contact
surface making contact with the gear 230T.

Apply total of 0.1g lubricating material
to the contact surface of the cams.

Apply 0.1g of grease
to the teeth.

(See figure 3-3-9)

(See figure 3-3-9)

Apply a drop of lubricating oil.

Apply a drop of lubricating oil.

27T

230T

28T

138T

138T

59T

66T

70T

68/20T

73/17T

46T

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands