Canon CLBP-460PS Service Manual Download Page 54 | Manualshive

Page: 54 / 566

background image

14. SERVICE menu

The SERVICE menu is a hidden menu exclusively for the field support staff. It is displayed after
the LANGUAGE SETUP menu when the power is turned ON with the MENU and ROTATE keys
held down.

The SERVICE menu allows you to adjust color density of the printer.
The sub-menus in the SERVICE menu are listed below. (Default values are in the square

brackets.)

NOTE:

The values, which are set while the printer is operating, do not become effective.
Therefore, sets the values when the printer is not operating.

1 - 44

CHAPTER 1

Submenu

ADJUST DENSITY?

ADJUST DENSITY
CYAN
ADJUST DENSITY
MAGENTA
ADJUST DENSITY
YELLOW
ADJUST DENSITY
BLACK
PRINT SERVICE PAGE

YES/NO [NO]

-7/-6/-5/-4/-3/-2/-1/0/
/1/2/3/4/5/6/7 [0]
-7/-6/-5/-4/-3/-2/-1/0/
/1/2/3/4/5/6/7 [0]
-7/-6/-5/-4/-3/-2/-1/0/
/1/2/3/4/5/6/7 [0]
-7/-6/-5/-4/-3/-2/-1/0/
/1/2/3/4/5/6/7 [0]
YES/NO [NO]

Options

Remarks

Specifies whether or not the toner den-
sity should be adjusted.
Sets density of cyan.

Sets density of magenta.

Sets density of yellow.

Sets density of black.

Prints a TEST PAGE with the changed
settings.

«
...
52
53
54
55
56
...
»

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CLBP-460PS

Brand: D-Link Pages: 12

Brand: Panasonic Pages: 24

Brand: Oki Pages: 40

Workio DP-1820E

Brand: Panasonic Pages: 38

Brand: Datecs Pages: 73

Brand: Datamax Pages: 12

E-Class Mark II

Brand: Datamax Pages: 40

Brand: Datamax Pages: 46

Brand: EasyThreed Pages: 4

Brand: EASYPRINT Pages: 37

Brand: Tally Pages: 202

Brand: Xerox Pages: 15

Brand: Xerox Pages: 9

DocuPrint 180 NPS Series

Brand: Xerox Pages: 172

Brand: Xerox Pages: 11

Brand: Xerox Pages: 8

Brand: Xerox Pages: 40

Brand: Xerox Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands