manualshive.com logo in svg

Canon CLBP-460PS, Service Manual

Share
Download
Canon CLBP-460PS Service Manual Download Page 287

Action:

Check the paper feeder feed roller drive gears and the drive transmission gears in
the printer side.  Replace any damaged or worn gears.  If the paper feeder is con-
nected via the duplexing unit, check the drive transmission gears in the duplexing
unit.

4) Poor contact between the paper feeder pick-up solenoid and paper feeder PCB

Action:

Reconnect the connectors between the paper feeder pick-up solenoid and paper
feeder PCB.

5) Poor contact between the paper feeder and printer

Action:

Reconnect the connectors between the paper feeder and printer.  Replace any dam-
aged connectors.

6) Defective paper feeder pick-up solenoid

Action:

Disconnect the paper feeder pick-up solenoid connector J3003 on the paper feeder
PCB.  Measure the resistance between the cable side connector J3003-2 (OPCLDRV)
and J3003-1 (+24VA).  If it is not about 160 , replace the paper feeder pick-up sole-
noid.

7) Defective paper feeder PCB

Action:

Replace the paper feeder PCB.

8) If the paper feeder is connected via the duplexing unit, execute step 6) and 14) in “3-5

duplexing unit block”.

9) Defective DC controller PCB

Action:

Replace the DC controller PCB.

4 - 33

CHAPTER 4

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands